=========================== R E L E A S E N O T E S =========================== Broadcom Advanced Server Program (BASP) Driver for Linux 2.4.x kernel Version 6.0.1 Copyright (c) 2000-2003 Broadcom Corporation All rights reserved. February 2, 2003 Table of Contents ----------------- 1. Overview 2. Limitation 3. Installation 4. Install - TAR archive 5. Install - RPM package 6. Files 7. Configuration - Red Hat Distribution 8. Configuration - Suse Distribution 9. Configuration and Startup for Other Linux Distribution 10. Startup scripts - Red Hat distributions 11. Configuration scripts - Red Hat Distributions 12. Broadcom NICE patches 13. Uninstall - RPM package 14. Removal of physical interface in Generic Trunking and 802.3ad mode 15. Known Problems 16. Logs 1. Overview ----------- BASP is a kernel module designed for 2.4.x kernels that provides load-balancing, fault-tolerance, and VLAN features. These features are provided by creating teams that consist of multiple NIC interfaces. A team can consist of 1 to 8 NIC interfaces and each interface can be designated primary, or hot-standby (SLB team only). All primary NIC interfaces in a team will participate in Load-balancing operations by sending and receiving a portion of the total traffic. Hot-standby interfaces will take over in the event that all primary interfaces have lost their links. VLANs can be added to a team to allow multiple VLANs with different VLAN IDs. A virtual device is created for each VLAN added. BASP supports Smart Load-balance (SLB), Generic trunking and IEEE 802.3ad Link Aggregation. In SLB and 802.3ad mode, all the NIC drivers must support Broadcom NIC Extension (NICE). In this release, several NIC drivers patched with NICE are included. * SLB mode works with all Ethernet switches without configuring the switch ports to any special trunking mode. Only IP traffic will be load-balanced in both inbound and outbound directions. * Generic trunking mode does not require NICE and can work with any NIC, however, it requires the Ethernet switch to support the technology and be properly configured. This mode is protocol-independent and all traffic should be load-balanced and fault-tolerant. * 802.3ad mode requires NICE drivers and Ethernet switches supporting IEEE 802.3ad Link Aggregation. This mode is protocol-independent and all traffic should be load-balanced and fault-tolerant. All the physical interfaces in the 802.3ad teams are defaulted to be LACP active. A 802.3ad team requires all the member NICs supporting NICE. All the member NICs, once in the 802.3ad team, will be set with the same MAC address. 2. Limitation ------------- BASP supports Red Hat 7.1, 7.2 and 8.1 beta. The following installation procedures work with these distributions. BASP has also been tested on SuSE 7.2 & 7.3, Caldera 3.1, Turbo Linux 7.0, Mandrake 8.1 and United Linux 1.0 based distribution. Minor modification to the Makefile may be required if problems are experienced when compiling BASP on other i386 Linux distributions. BASP supports Red Hat Linux for IA-64 architecture. BASP supports SuSE Linux for AMD x86_64 architecture. VLANs are only supported by Broadcom NetXtreme Gigabit Ethernet. As opposed to VLANs support in other platforms, e.g. Windows and Netware, VLANs are not supported by Alteon Acenic driver (acenic.c). 3. Installation --------------- For users of Red Hat 7.1, 7.2 (i386 and IA-64) and Suse Linux (i386 and x86_64) follow instructions in "Install - RPM package" section. For users of other Linux i386 and IA-64 distribution, follow instructions in "Install - TAR archive" section. 4. Install - TAR archive ------------------------ BASP for Linux is shipped in mixed forms, where the platform and kernel specific files are in source code, and the core file is in object form. Three packages are shipped in this release: two tar archives and two RPM package. "basplnx-{version}.i386.tgz" is the tar archive for i386 platform, "basplnx-{version}.ia64.tgz" is the tar archive for IA-64 platform, "basplnx-{version}.x86_64.tgz" is the tar archive for AMD 64 bit platform. To uncompress and expand the tar archive, run % tar xvfz basplnx-{version}.{arch}.tgz The installation process involves the following steps: (1) To build kernel module, "basp.o", % make Note that the Make process will automatically build the correct module for different kernel options, e.g. symbol versioning and SMP support. There is NO need to define -DMODVERSIONS in the Makefile. (2) To create device file and to copy files, % make install (3) To update the module reference, % depmod -a (4) To load the driver, % insmod basp (5) Follow the "Configuration and Startup for Other Linux Distribution" section to set up the teams. 5. Install - RPM package ------------------------ (1) To install the RPM source package, run % rpm -i basplnx-{version}.src.{arch}.rpm (2) Change directory to the RPM path and build the binary driver for the kernel % cd /usr/src/redhat % rpm -bb SPECS/basplnx.spec Note that the RPM path is different for different Linux distributions. For those distributions with RPM v4.1 or later, use "rpmbuild" comannd instead of "rpm". (3) Install the newly built package % rpm -i RPMS/i386/basplnx-{version}.{arch}.rpm The driver and other required files will be automatically installed. (4) To load the driver, % insmod basp (5) Follow the Configuration section to set up the teams. 6. Files -------- Makefile makefile baspcfg precompiled configuration utility bcmtype.h commonly use type header file blf.c BASP module entry points blf.h ioctl interface blfcore.h core interface blfcore.o pre-compiled core object blfopt.h automatic generated header file by Make blfver.h version header file nicext.h NICE header file pal.c platform abstraction implementation pal.h header for paltform abstraction release.txt this file nice-2.2.16 NICE enabled driver for 2.2 kernel nice-2.4.16 NICE enabled driver for 2.4 kernel scripts contains sample scripts scripts/basp init script, goes to /etc/init.d scripts/baspteam start/stop script, goes to /etc/basp scripts/baspif start/stop network i/f, goes to /etc/basp scripts/team-sample sample script of SLB team with 3 NICs scripts/team-gec sample script of GEC team with 3 NICs scripts/team-vlan sample script of SLB team with 2 VLANs basp.4 man page baspcfg.8 man page for baspcfg utility 7. Configuration - Red Hat Distribution --------------------------------------- The BASP distribution includes an utility program and several scripts for team configuration. Following steps for Red Hat Linux distributions only. Most of the steps are only required to be performed after the first time installation. Step 2 "Modify the configuration script" should be performed whenever there is any change to the team configuration. For users of other Linux distributions, follow instructions in the "baspcfg" section. The configuration process involves the following steps: (1) Copy a configuration script from "/etc/basp/samples" directory to "/etc/basp" directory. Note the configuration script must be prefixed with "team-". (2) Modify the configuration script to (a) change the team type (b) add/delete physical network interfaces (c) add/delete virtual network interfaces (d) assign IP address to each virtual network interface The syntax of the configuration script can be found below. Note that when configuring Teaming, at lease one Primary Adapter is required. (3) Manually start the team for the first time, % /etc/init.d/basp start Note that this step is only required for the first time installation. The team configuration will be automatically started on subsequent reboots. Note that if not all the virtual network interfaces are configured with IP address, there will be an error message in starting the BASP team. When this happens, repeat step (2) to configure IP address for all the virtual network interfaces. Note-1) Forming multiple teams is possible by copying the sample files into "/etc/basp/team-" and modifying this file as described in the sample file. Note-2) In order to create more that one virtual interface (VLAN) for each team, refer to the respective description section in the sample files. 8. Configuration - Suse Distribution --------------------------------------- The BASP distribution includes an utility program and several scripts for team configuration. Following steps for Suse Linux distributions only. Most of the steps are only required to be performed after the first time installation. Step 2 "Modify the configuration script" should be performed whenever there is any change to the team configuration. Since Suse distribution does not automatically load driver for the network device unless the device is configured with IP address, users must manually use "yast2" or configure /etc/rc.config file to ensure proper network drivers loaded during init time. For users of other Linux distributions, follow instructions in the "baspcfg" section. The configuration process involves the following steps: (1) Copy a configuration script from "/etc/basp/samples" directory to "/etc/basp" directory. Note the configuration script must be prefixed with "team-". (2) Modify the configuration script to (a) change the team type (b) add/delete physical network interfaces (c) add/delete virtual network interfaces (d) assign IP address to each virtual network interface The syntax of the configuration script can be found below. Note that when configuring Teaming, at lease one Primary Adapter is required. (3) Manually start the team for the first time, % /etc/init.d/basp start Note that this step is only required for the first time installation. The team configuration will be automatically started on subsequent reboots. Note that if not all the virtual network interfaces are configured with IP address, there will be an error message in starting the BASP team. When this happens, repeat step (2) to configure IP address for all the virtual network interfaces. Note-1) Forming multiple teams is possible by copying the sample files into "/etc/basp/team-" and modifying this file as described in the sample file. Note-2) In order to create more that one virtual interface (VLAN) for each team, refer to the respective description section in the sample files. 9. Configuration and Startup for Other Linux Distribution --------------------------------------------------------- "baspcfg" is a command line tool to configure the BASP teams, add/remove NICs and add/remove virtual devices. This tool, may be used to configure your own startup script files. Please read your distribution specific documentation for more information on your distributions's startup procedure. Following is the usage of this tool: baspcfg v6.0.1 - Broadcom Advanced Server Program Configuration Utility Copyright (c) 2000-2003 Broadcom Corporation. All rights reserved. usage: baspcfg commands: addteam -- create a team delteam -- delete a team addva [macaddr] -- add a virtual adapter to a team delva -- del a virtual adapter from a team bind -- bind a physical adapter to a team unbind -- unbind a physical adapter from a team show [tid] -- display team configurations where tid -- An unique ID for each team, starting from 0 type -- Team type: 0=SLB, 1=FEC/GEC, 2=802.3ad tname -- ASCII string of the team vlan_id -- VLAN ID: from 1 to 4094, 0=untagged or no VLAN vname -- ASCII string of the virtual device macaddr -- MAC address (optional), e.g. 00:10:18:00:11:44 role -- Role of the physical device: 0=primary, 1=hot-standby device -- ASCII string of the physical device, e.g. eth0 Following sample startup script should be used to start the BASP after first time installation and configuration, or in the subsequent reboots. #!/bin/bash # load basp module insmod basp # create new team baspcfg addteam 0 0 team-one # bind physical interfaces / two primary one backup baspcfg bind 0 0 eth0 baspcfg bind 0 0 eth1 baspcfg bind 0 1 eth2 # create the virtual interface baspcfg addva 0 0 sw0 # bind ip address to virtual interface and initialize ifconfig sw0 192.168.0.1 up Note: Baspcfg command can only be executed in Super User mode only, configure with other login mode will yield "Permission Denied. Must be root to manage BASP" error message. When configuring Teaming, at lease one Primary Adapter is required. 10. Startup scripts - Red Hat distributions ------------------------------------------ (1) basp This script is intended to be installed in /etc/init.d directory. After copying the script, run "chkconfig --add basp". This script will be executed at runlevel 2, 3, 4 and 5. When "basp" is run, it will search the /etc/basp directory to list all the files with "team-" prefix, and then it will invoke "baspteam" script to add or delete the teams. It is normal that each "team-*" file in /etc/basp represents 1 team. (2) baspteam This script is called by "basp" script to add or delete a team. To install, create "/etc/basp" directory and copy this script over. To manually add a team: % baspteam team-sample add To delete a team: % baspteam team-sample del Note that "team-sample" is the configuration script. (3) team-sample This script contains a SLB team configuration with 3 NICs: eth0, eth1 and eth2. The team name is "TeamSample". All 3 NICs are primary. One virtual interface is also created for this team and the name of the virtual interface is "sw0". "sw0" is the device that "ifconfig" should be run against to set up the IP address. VLANs are not enabled in this script. This script and "team-gec" are intended to be customized. Refer to the configuration scripts section for details. This script should be copied to /etc/basp directory and retain the "team-" prefix. (4) team-gec This configuration script creates a GEC team with 3 network interfaces, eth0, eth1 and eth2. The team name is "TeamGEC". All 3 NICs are primary. One virtual interface is added to the team with the name "sw0" and VLANs are not enabled. This script and "team-sample" are intended to be customized. Refer to the configuration scripts section for details. This script should be copied to /etc/basp directory and retain the "team-" prefix. 11. Configuration scripts - Red Hat and Suse ------------------------------------------- Both "team-sample" and "team-gec" are configuration scripts that follow the same syntax, as following TEAM_ID: this number uniquely identifies a team. TEAM_TYPE: 0 = SLB, 1 = Generic Trunking/GEC/FEC, 2 = 802.3ad TEAM_NAME: ascii name of the team TEAM_PAx_NAME: ascii name of the physical interface x, where x can be 0 to 7. TEAM_PAx_ROLE: role of the physical interface x 0 = Primary, 1 = Hot-standby. This field must be 0 for Generic Trunking/GEC/FEC team. TEAM_VAx_NAME: ascii name of the virtual interface x, where x can be 0 to 63 TEAM_VAx_VLAN: 802.1Q VLAN ID of the virtual interface x. For untagged virtual interface, i.e. without VLAN enable, set it to 0. The valid VLAN ID can be 0 to 4094. TEAM_VAx_IP: IP address of the virtual interface x. The format should be aa.bb.cc.dd. TEAM_VAx_NETMASK: Subnet mask of the virtual interface x. The format should mm.nn.oo.pp. Note: Teaming scripts are intended for Red Hat distributions ONLY, use with other Linux distribution will causes ERROR. 12. Broadcom NICE patches ------------------------- Also included in this release are network device drivers patched with Broadcom NICE support. These drivers are originally taken from the Linux 2.4.16 kernel distribution. To install patched drivers: (1) Copy the Broadcom NICE header file, "nicext.h", to the appropriate Linux kernel include directory, e.g. % cp /usr/src/nice-2.4.16/nicext.h /usr/src/linux/include/linux (2) Rename the original network device driver under the Linux kernel source tree, "/usr/src/linux/drivers/net". (3) Copy the patched drivers to the Linux kernel network driver source directory, i.e. "/usr/src/linux/drivers/net". (4) Follow the kernel rebuild instructions to configure kernel support for these drivers, i.e. % cd /usr/src/linux % make config (5) If the patched drivers are configured into the kernel, goto step (7). If the patched drivers are configured as modules, goto step (6). (6) In the case of supporting only the module version of these drivers, it is possible to simply run the following to compile patched drivers and to install them into the proper module directory: % make modules % make modules_install There is no need to compile the complete kernel. Goto step (8). (7) Rebuild the kernel to compile these patched drivers % make clean % make dep % make (8) Either reboot the system or unload/load the patched modules. Run configuration scripts to test the patch. 13. Uninstall - RPM package --------------------------- To uninstall RPM package, % rpm -e basplnx and to reboot the system, % reboot 14. Removal of physical interface in Generic Trunking and 802.3ad mode ---------------------------------------------------------------------- In Generic Trunking and 802.3 ad mode, all the physical and virtual interfaces belonging to a team have the same MAC address. This MAC address is the same address as that of the first physical interface bounded to the team. In the case that this first physical interface is removed dynamically from the team using "baspcfg" tool and bounded to the protocol directly, this could lead to a duplicate MAC address problem on the network. Note that if the removed physical interface does not participate in any traffic, there will not be any problem. To properly remove a physical interface, follow the steps listed below: (1) Backup the original team configuration script % cp /etc/basp/team-gec /etc/basp/backup-gec Note-1) "team-gec" is the name of the configuration script. Note-2) "backup-gec" is the name of the backup script. The name of the backup script must NOT be prefixed with "team-". (2) Modify the team configuration script to remove the physical interface (3) Stop the running team % /etc/basp/baspif /etc/basp/backup-gec stop % /etc/basp/baspteam /etc/basp/backup-gec del (4) Re-start the team % /etc/basp/baspteam /etc/basp/team-gec add % /etc/basp/baspif /etc/basp/team-gec start 15. Known Problems ------------------ (1) DHCP address problem We have identified that there is incompatiblity between SLB and IP address obtained via DHCP. In the lab, we have seen that the virtual network interface lost the IP address after running for a period of time. To solve the problem, always assign static IP address to the virtual network interfaces. (2) 802.3ad team member links disconnect and reconnect continuously when connects to the HP2524 switch. This is a 3rd party issue. It is seen only when configuring an 802.3ad team with greater than 2 members on the server and connecting an HP2524 switch, with lacp enabled as passive or active. The HP switch will show an lacp channel being brought up successfully with only 2 members. All other member's links will disconnect and reconnect. This does not occur with a Cisco Catalyst 6500. (3) To avoid fail-over issues when using BASP, make sure that spanning tree is disabled on the switch that the network adapter is connected to. 16. Logs -------- v6.0.1 - Added RPM support for AMD 64-bit on SuSE 8.1 beta. - Added RPM support for Red Hat 8.1 beta. - Added RPM support for United Linux 1.0 based distributions. - Fixed potential duplicated MAC address problem in Generic Trunking or IEEE 802.3ad Link Aggregation mode. - Minor documentation cleanup. v3.0.14 - Fixed memory leak problem caused by baspcfg. v3.0.13 - Man pages correction. v3.0.12 - Added "MODULE_LICENSE("Proprietary")". - Clarification of the MAC address error message. v3.0.11 - Added IP address parameters to the team configuration script. v3.0.10 - Fixed init script to start BASP properly on Suse Linux. v3.0.9 - Add RPM support for Suse 7.3. v3.0.8 - Fixed installation script to handle already existing directories. - Minor changes in documentation. v3.0.7 - Added dynamic assigned major device number support. - Discontinued Linux 2.2.x kernel support. v3.0.6 - Fixed Prod00003107: Load balancing does not occur on multiple hot-standby adapters. v3.0.5 - Support BASP MIBs. v3.0.4 - Added installation of nicext.h file to the current kernel source tree. - Enhanced /proc file system support. v3.0.3 - Fixed a buffer overrun issue in the IEEE 802.3ad mode . - Fixed the virtual adapter deletion issue. v3.0.2 - Fixed various IEEE 802.3ad Link Aggregation problems. - Added NICE enabled drivers for 2.4.16 kernel. v3.0.1 - Added support of IEEE 802.3ad Link Aggregation. v2.0.5 - Fixed lock-up problem with 2.4 SMP kernel. v2.0.4 - Enhanced install documentation for non-Red Hat distribution. - Minor documentation changes. - Corrected the error message displayed by "baspcfg" utility. - Added removal of empty directories at RPM un-install time. v2.0.3 - Changed default BASP management device to 250 to facilitate out of box installation. - Added access control to allow that only root can manage BASP. proc file system is still visible to all users. v2.0.2 - Added support to the Linux 2.4.2 kernel for IA-64 architecture. v2.0.1 - Fixed the server hang problem caused by removing a physical interface without first detaching from the team. - Added proc fs support for reporting team configuration. v1.2.2 - Enhanced "basp" init script to work with other Linux distrbutions. - Fixed jumbo frame problem. v1.2.1 - Added support to Red Hat 7.1 release. - Added man pages. v1.2.0 - Added support to the Linux 2.4.0 kernel. v1.1.13 - Added check to prevent the removal of the primary physical interface in a generic trunking team. Such removal might cause duplicated MAC addresses on the network. v1.1.12 - Updated the release note. v1.1.11 - Fixed the problem of adding the same virtual interface twice. - Correctly attribute packet counters to the correct virtual interfaces when VLAN is enabled. v1.1.10 - Fixed the problem that invalid VLAN can be added but not removed. - Add removing of BASP teams in RPM de-installation. - Added usage and argument checking to basp script. - Fixed the problem that init script fails with multiple teams. - Fixed the problem in switching runlevels. v1.1.9 - Enhanced RPM packaging support. - Changed "basp" script to run at priority 11, which is right after "network" script. - Automatically detect the presence of "kgcc" and use "kgcc" to get around Red Hat 7.0 compiler problem. - Added "baspif" script to start and stop network interfaces. v1.1.8 - Added RPM packaging. v1.1.7 - Fixed failure of server originated ping with VLAN enable. - Fixed loss of network connection under heavy traffic on SMP system. v1.1.6 - Changed both module and device name to "basp.o" and "/dev/basp" respectively for consistency. - Added startup scripts. - Enhanced Generic Trunking support by automatically programing the MAC addresses. - Addressed VLAN deletion issue. v1.1.5 - Fixed Generic Trunking problem. - Improved error messages in runing baspcfg utility. - Added Generic Trunking sample script. v1.1.4 - Added "show" command in baspcfg to display team configurations and status. - Improved module build process for MODVERSIONS and SMP kernel. - Display module build options in syslog during module load time. - Display blfcore.o version during module loading time. - Major changes in Makefiles to improve the build process. - Improved build documentation. - Changed to new baspcfg usage to the release.txt. - Added documentation to describe how to install NICE patched drivers. v1.1.3 - Fixed pal_read_mii() function. v1.1.2 - Fixed linux/if.h dependency problem which prevented BASP from detecting NICE supported driver on older kernels.