                      Modificaciones para FT-5100.
                      ============================

Ampliacion de Banda:
--------------------

La ampliacion de banda se realiza por medio de las resistencias de valor 0,
situadas en la placa de control (tras el display)

1 - Desmontar los 12 tornillos que sujetan ambas tapas. Cuidado con el altavoz
ya que va sujeto a presion entre un puente de plastico y la tapa exterior,
2 - Desmontar los 2 tornillos laterales que sujetan el frontal. 
3 - Retirar el frontal con mucho cuidado para no romper las cintas de plastico
4 - Localizar las resistencias de valor 0 con ayuda del grafico ya que no 
vienen numeradas. Estas resistencias estan justo delante de los conectores que
unen la cinta de plastico a la placa de control.

  Resistencia:   62 - 66 - 68 - 72
  Origen     :    A    C    A    C       144-146, 430-440
  Abierto    :    C    A    C    A       130-180, 400-510
  

       PLACA DE CONTROL

                                                           -------
    X X X  X O X O O X X X X O O X X                       |     | 2C3
           7 7 7 6 6 6 6 6 6 6 6 6    X X X X X            |     |  3R
           2 1 0 9 8 7 6 5 4 3 2 1                         ------- HD61620H
    __________________       ___________________
                
                  CONECTORES JP


5 - Encender el equipo para programar los margenes de frecuencias de RX y TX 
para cada banda. Al encender el equipo, el display mostrara las frecuencias de
300.000 MHZ para UHF y 20.000 MHZ para VHF, con las memorias "1" parpadeando.
    Se inicia el proceso por la banda de UHF. Se elige el margen inferior para
RX y se pulsa D/MR. El "1" pasa a "2".
    Se elige el margen superior RX y se pulsa D/MR. El "2" pasa a "3".
    Se elige el margen inferior TX y se pulsa D/MR. El "3" pasa a "4".
    Se elige el margen superior TX y se pulsa D/MR. El "4" parpadeante
desaparece y cambia al VFO de VHF. Se repite el mismo proceso para la banda de

VHF.

EB5HLN@EB5HLN.EAA.ESP.EU


--------------------------------------------------------------------------


                MODIFICACION PARA YAESU FT 5100
                ===============================


Esto es una modificacion para abrir de frequencia la emisora   
bibanda  YAESU FT-5100.Si seguis todo los pasos uno a uno
podreis tener un cobertura en VHF de 125 MHz a 175 MHz y en
UHF de 405 MHz a 465 MHz tanto en RX como en TX.
Intentare explicarlo lo mas sencillo posible para que tambien
podais hacerlo los que no esteis muy acostumbrdos a
"CACHARREAR".
Bueno, pues manos a la obra y seguir paso a paso las
instrucciones y seguro que funcionara.

1.- Preparar un soldador de 30 W con la punta fina (cuando mas
fina mejor), unas pinzas y unos trozitos de cable de aprox.
5 cm de lomgitud.El soldador y las pinzas son para quitar dos
resistencias SMD (que son la mar de pueteras) y ponerlas en
otro lugar (en realidad estas resistencias son puentes).Los
que no querais volver a poner las SMD poner en su lugar los
trozitos de cable,que sera mas facil y hacen la misma funcion.

2.- Quitar las tapas superior e inferior,retirando los doce
tornillos que lleva, prestando atencion al altavoz que esta
suelto.

3.- Proceder a separar el frontal del cuerpo, retirando los
dos tornillos laterales.

4.- En la unidad de control, que esta detras del display,
localizar a la izquierda del MICROPROCESADOR "HD61602H",
( integrado cuadrado con muchas patitas )encima de dos
conectores, una fila de resistencias SMD.
( VER ESQUEMA )

5.- Configurar estas resistencias (vuelvo a decir que en
realidad son puentes), de tal forma que que las resistencias
R-62 y R-68 esten puestas, y que las resistencias R-66 y R-72
quitadas.  ------ EL RESTO NO TOCARLAS. ------
Ya sabeis desoldar con mucho cuidado de no calentar demasiado
las pistas para que no se estropen y despues soldar en los
otros puntos con mucho cuidado.
Fijaros bien primero cual teneis que quitar y donde teneis que
volver a soldarlas o en su defecto soldar el cablecito que os
haga de puente.
En el esquema que viene a continuacion se pueden ver los dos
conectores y la fila de resistencias encima. A la derecha esta
el microprocesador (el integrado cuadrado que tiene un monton
de patas).



6.- ESQUEMA.

      = RESISTENCIA PUESTA DE ORIGEN.

      = RESISTENCIA QUE FALTA DE ORIGEN.

 PLACA DE CONTROL (PARTE TRASERA DEL DISPLAY)

     Localizacion de Resistencias/Puentes
       
                    PONER      PONER                         
            QUITAR    QUITAR               MICRO
          R72 R70 R68 R66 R64R62               2C3             
                                          3R
                              HD61602H 
                            
            R71 R69 R67 R65 R63 R61         
             
  IIIIIIIIIIIIIII              IIIIIIIIIIIII
 ic            ic 
              

    CONECTOR JP                    CONECTOR JP   


7.- Cerrar la emisora, invirtiendo los pasos 2 y 3.

           BUENO YA HEMOS ACABADO LA PARTE MECANICA,
                AHORA VAMOS CON LA PROGRAMACION.

                HACERLO DESPACIO Y LEER BIEN PRIMERO LAS
                INSTRUCCIONES.

8.- Encender el equipo y programar los limites:

A.- En el angulo superior izquierdo, aparecera un "UNO" (1);
Ajustar el limite inferior de RX en UHF a 405.000 y pulsar el
boton D/MR que esta arriba a la izquierda del todo.

B.- Con un "DOS" (2), ajustar el limite superior de RX en UHF
a 465.000 y pulsar D/MR.

C.- Con un "TRES" (3), ajustar el limite inferior de TX en UHF
a 405.000 y pulsar D/MR.

D.- Con un "CUATRO" (4), ajustar el limite superior de TX en
UHF a 465.000 y pulsar D/MR.

     OJO: AL EFECTUAR ESTE PASO, EL DISPLAY CONMUTARA
     AUTOMATICAMENTE A LA BANDA DE VHF, PARA PROGRAMAR LOS
     LIMITES.

E.- Con un "UNO" (1), ajustar el limite inferior de RX en VHF
a 125.000 y pulsar D/MR.

F.- Con un "DOS" (2) ajustar el limite superior de RX en VHF a
175.000 y pulsar D/MR.

G.- Con un "TRES" (3) ajustar el limite inferior de TX en VHF
a 125.000 y pulsar D/MR.

H.- Con un "CUATRO" (4) ajustar el limite superior de TX en
VHF a 175.000 y pulsar D/MR.

     Bueno con esto hemos acabado de hacer la modificacion y
vuestro equipo debe de funcionar ya con las bandas abiertas.

Espero que tambien los menos expertos se aclaren con estas
instrucciones.

    
--------------------------------------------------------------------------

                          MODIFICATION FT-5100
                          ====================


The mods are at the pc of the frontpannel.


Locate the panel unit jumper points R40XX  X = Short


TYPE   FREQUENTIERANGE    59   61  62  64  65  66  67  68  70  72
----   ---------------    --   --  --  --  --  --  --  --  --  --
 A1    144-148 430-450     x    x   x               x
 A2    140-174 430-450     x    x   x               x           x
 A3    140-174 430-450     x    x   x               x       x
 B1    144-146 430-440          x       x   x   x   x       x   x
 B3    104-174 430-440          x       x   x   x   x       x
 B5    140-160 430-440          x       x   x   x   x   x       x
>C1    144-146 430-440          x       x   x       x       x   x
 C3    140-174 430-440          x       x   x       x       x
 C5    140-160 430-440          x       x   x       x   x       x
 D     144-146 432-438          x   x       x   x   x       x   x
FREE                                x   x               x   x

FREE BAND Please keep "D/MR","REV" and "F/W" WHILE POWER ON.
          1/Set the low edge of RX freq. and press D/MR
          2/Set the high edge of RX freq. and press D/MR
          3/Set the low edge of TX freq. and press D/MR
          4/Set the high edge of TX freq. and press D/MR


     =UHF rep.shift : TYPE A = 5 Mhz   B = 7,6 Mhz   C = 1,6 Mhz


--------------------------------------------------------------------------

Expanded Receive:

	Good Effect: enable extended receive coverage
		New range:   128-180MHz and 420-475MHz
	Bad Effect: disable automatic repeater shift selection.

	Warning: You must have a very steady hand or else!  A
	   magnifying glass would help too.

	1) Disconnect DC Power cable from radio. ALWAYS!

	**Caution** NEVER TRY TO TAKE APART (DISASSEMLBLE) THE FRONT
	            CONTROL HEAD. It will void your warranty.

	2) Remove (6) screws from Top Cover of Radio and (6) screws
	   from Bottom Cover of radio.
	3) Remove Top & Bottom Covers from Radio (Be careful of speaker
	   falling out).
	4) Remove the (2) silver screws on each side of the radio
	   holding front control head to main body of radio.
	5) Carefully pull away (a few inches) the Control Head from
	   the radio body. CAREFUL with the Ribbon Cables.

	**NOTE** There are no numbers on the circuit board so you will
	         have to match up with the diagram below.

	6) On the rear of the Control head locate, Unsolder and remove
	   jumper Pad R4072.
	7) Solder across jumper pads: R4070 R4068 & R4064 (use wire or
	   0 Ohm resistor)

	**NOTE** If you want to change the D/MR button on the
	         microphone to do Band Switching, now is the time.
	         See the next mod.

	8) Install Front Control head, Speaker, Top and Bottom Covers
	   and Reconnect Power to the Radio.
	9) Press and hold [D/MR] [F/W] [REV] Keys and turn on the Radio.
	   Radio will now show 300.000 & 20.000 on Display.
	10) Set UHF Rx Low - Press [MHz] and dial 420.00, press [D/MR]
	11) Set UHF Rx High- Press [MHz] and dial 475.00, press [D/MR]
	12) Set UHF Tx Low - Press [MHz] and dial 420.00, press [D/MR]
	13) Set UHF Tx High- Press [MHz] and dial 450.00, press [D/MR]
	14) Set VHF Rx Low - Press [MHz] and dial 128.00, press [D/MR]
	15) Set VHF Rx High- Press [MHz] and dial 180.00, press [D/MR]
	16) Set VHF Tx Low - Press [MHz] and dial 140.00, press [D/MR] 
	17) Set VHF Tx High- Press [MHz] and dial 150.00, press [D/MR] 
	18) Set UHF offset - Press [F/W] then [RPT] dial 5.000 press [RPT] 
	19) Set UHF tuning - Press [F/W] then [REV] dial 25.0  press [RPT]
	20) Set VHF offset - Press [F/W] then [RPT] dial 0.600 press [RPT] 
	19) Set VHF tuning - Press [F/W] then [REV] dial 20.0  press [RPT]
		(VHF tuning step varies by state -- many use 15.0)

	Diagram: [there are no tabs in this section - ed]

        Ok, here's where it gets tricky, but so you know, a '
           represents a jumper.

                !Ribbon  !                       !Ribbon  !
                !Cable   !                       !Cable   !
            ____!J4002   !_______________________!J4001   !_____________
            !   !________!                       !________!            !
            !                Rear view of FT-5100                      !
            !    ____        Control Head.                             !
            !    !  !                                                  !
            !    !__!                                        !
            !                          !
            !                        R R R R R R R R R R R R R  R R R  !
            !                        4 4 4 4 4 4 4 4 4 4 4 4 4  4 4 4  !
            !                        0 0 0 0 0 0 0 0 0 0 0 0 0  0 0 0  !
            !                        5 6 6 6 6 6 6 6 6 6 7 7 7  0 0 0  !
            !                        1 1 2 3 4 5 6 7 8 9 0 1 2  1 3 4  !
            !__________________________________________________________!
        
        
        Stock US Jumpers        After Mod. Jumpers
        R4001                   R4001
        R4003                   R4003
        R4004                   R4004
        R4051                   R4051
        R4061                   R4061
        R4062                   R4062
                                R4064
        R4067                            <- for D/MR button mod
                                R4068
                                R4070
        R4072



--------------------------------------------------------------------------


Band Switching via D/MR button on microphone:

	Effect: D/MR button on microphone performs band switching
	   rather than D/MR function.

	1-5) as in above mod
	6) Remove the jumper on Pad R4067
	7) skip above step 7
	8) continue with step 8 above


--------------------------------------------------------------------------


Backlight Control:

	Effect: manual control of backlight

	1) Hold down the MHZ key and turn radio on
	2) Use tuning knob to adjust brightness
	3) When FUNC is active, the tuning knob will adjust
	   brightness again.
	4) You can restore automatic control by repeating step 1.

	Notes:  Manual is fuzzy on this feature.

	Attributed: Yaesu


--------------------------------------------------------------------------

Crossband Repeat (reported as working on 5100 and 5200):

	Effect: Enable crossband repeat

	1) Dial up two frequencies you want to crosslink (be sure to
	   pay attention to transmit offsets, if any)
	2) Turn radio off.
	3) Hold down the RPT key and turn radio on

	Result:  The tone encode/decode flags and the -+ flags will be
	flashing and the radio will be in low power mode.  When either
	band's squelch opens, the other band is moved into the primary
	frequency display and the transmitter keys.  Audio link
	appears to be speaker to mike.

	Exit crossband repeat mode by repeating steps 2 and 3 above.

	Attributed: Yaesu


--------------------------------------------------------------------------


Crossband Audio Enhancement:

	Effect: unmuffle crossband audio

	Connect a 27K ohm resistor between the audio-in and auido-out
	leads on the data jack (inside the shell of a mini plug, that
	is).  The mic element stays live while in xband operation.  It
	is a good idea to remove the mic from the rig while cross
	banding if you need/want to eliminate ambient audio.




--------------------------------------------------------------------------


Transmitter Timeout:

	Effect: automatically limit transmitter "on" time

	1) Hold down the HIGH/LOW button and turn radio on
	2) Use tuning knob to change the number in left VFO.  This
	   number is number of minutes for the timeout timer.  The
	   factory default appears to be 15 minutes.
	3) Transmitter shuts off with "Err" displayed in VFO if the
	   time limit is exceeded.


--------------------------------------------------------------------------

The "P" Key on the microphone:


	I was curious about that "P" key on my FT-5100, so I called
	Yeasu and they explained the situation.  They designed the the
	mic to accomidate "future products".  The "P" key is there to
	be taken advantage of at a later date by other models.  They
	just did not want to re-design the mic again within a short
	period of time.


--------------------------------------------------------------------------


I own a FT-5100 and became interested in the Remote Control Mike, not
for its wirelessness, but because it can control most of the radio's
features via a serial data stream through the mircophone jack. 
Although I do not own the wireless mike, I was able to build an
interface between my PC and my 5100.  It is somewhat similar to the
CAT interface I have built for my FT-757 HF rig, but mostly like the
interface described in the FT-912R manual (loaned to me via a friend
from Yaesu). I have recently been working on a micro-controller
based radio controller which I use for transmitter hunts, and other
ham related activities, and I plan to allow it to control my 5100
soon, but so far I have only controlled the radio from my PC.  When
using my PC as the source for the serial data, I used a MAX232 chip
for a level conversion between the +/- 12 volts levels on the
computer and the 0-5 volt levels on the radio.  

The serial data paramaters are 4800 N82.  The commands sent to the
radio are simple one byte instructions.  The RMC mode ON command (16)
must be sent before any other command.  When the RMC mode is ON, a
small LCD "RMC" icon will light on the display (see owners manual
under Display).  Also, the Vol, Sql, and Bal knobs are disabled when
in the RMC mode because they will be controlled via serial commands,
but all other buttons are still active.  

The commands are as follows:

0  - RPT            12 - CALL             24 - SQL Up
2  - REV            14 - BAND             26 - VOL Up
4  - MHZ            16 - RMC              28 - BAL Right
6  - D/MR           18 - SUB              30 - BAL Left
8  - TONE           20 - PAGE             32 - SQL Down
10 - LOW            22 - F/W              33 - VOL Down

The interface I built simply wired mike port pin 7 to serial ground
and pins 1 and 3 each through a diode then together, to the serial
source.  Note: I am not a hardware person!  Use this hardware at your
own risk.  

 +----1 7-------------- GND 
   2 8 6                      (These can be connected to a MAX232
 +--3 5   +-+-------- SER IN   or the FIF-232C pins 1 and 3)
   4     +--->--+  +----->----+

You can wire 1 and 3 together first, then through 1 diode, but that
disables the UP and DOWN buttons.

I will continue to study this more.  If anyone would like to know
more, or has any corrections or feedback, please email me.    


--------------------------------------------------------------------------

             MODIFICACIONES FT-5100 para 9600 Baudios.



  Dada  la gran  cantidad de  mensajes referentes  a posibles  problemas  para
trabajar packet a 9600 baudios con  el FT-5100, me puse en contacto  con ASTEC
para tratar de averiguar algo al respecto.
  Por parte  de ASTEC  se me  ha autorizado  a difundir  esta informacion.  Su
extraeza ha sido que no fuera ya de dominio publico, dado que con este fin lo
han pasado varias veces.



  Parece ser que el problema detectado SOLO AFECTA A LAS PRIMERAS unidades,
osea que  es muy  posible que  muchos de  estos aparatos  trabajen bien a 9600
baudios.

  MAIN UNIT
1 - Quitar R1102, C1194 y C1196
2 -  Adaptar una  resistencia de  100 K  para las  salidas al PLL de 144 y 432
segun esquema:


                          R1073              C1162
                      ----/\/\/\--------------I I------ a Unidad PLL 144
                                    |        -   +
           J1007        100K        |
Data IN      *---------/\/\/\-------|  
                 |   
                 |      100K
                 |-----/\/\/\-------|
                                    |        -   +
                     ----/\/\/\---------------I I------ a Unidad PLL 430
                         R1078               C1169


  144 PA UNIT
1 - Quitar C104 y C105

  AF UNIT
1 - Quitar C501, C513, R504, R512, R531 y R 526
2 - Adaptar una resistencia de 10 K, una de 56 K y un Transistor DTC124EK para
cada uno de los circuitos de Vhf y UHF segun esquema.


         J501     10K                   56K                    J502    
Det V (4) *------/\/\/\----------------/\/\/\--------------------* (14) DATA
                          |                                   |
                          \         22K          J502         |
                 DTC124EK  \|-------/\/\/\---* (11) SQL V     |
                           /|     |                           |
                          V   22K |                           |
                         |--/\/\/\-                           |
                      -------                                 |
                      //////                                  |
                                                              |
Det U (5) *------/\/\/\----------------/\/\/\------------------
                          |
                          \              22 K       J502
                 DTC124EK  \|-----------/\/\/\-------* (10) SQL U
                           /|        |
                          V    22K   |
                          |--/\/\/\---
                       -------
                       //////    

Datos de YAESU EUROPA facilitados por ASTEC.


     73 de Eduardo!!
EB5HLN @ EB5HLN.EAA.ESP.EU
    Benidorm - IM98wm
     [25-Ago-16:04]


-------------------------------------------------------------------------



